YOU ARE AT THE INTERNATIONAL WEBSITE, SWITCH TO: | NETHERLANDS | USA |  
   
 
 
   
  Roughening Tools  
   
         
 

For the roughening of diamond drilled holes. SDS-Max. Qty./1

Instructions for Use:

  • Machine is leaning to one side with the tool in the hole without pressure.
  • From this point make 3 revolutions leaning to the outside, while spinning the motor.
  • The bottom side of the tool rattles along the bottom part of the hole. The top half will roughen the top part.
   
 
Description Anchor Hole Diameter Drilling Depth EAN Part Nr.
Roughening Tool M16 18 mm 125 mm 8714345170930 3.900.040
Roughening Tool M20 22 - 25 mm 170 mm 8714345170947 3.900.041
Roughening Tool M24 26 - 28 mm 210 mm 8714345170954 3.900.042
Roughening Tool M27-30 32 - 35 mm 280 mm 8714345170961 3.900.043
 
     
  Mixing Nozzles   Piston Plugs  
     
 

For BIS Cartridges. • Qty./100

 

For better distribution of the Injection Mortar in deep and horizontal holes • Qty./10

 
 
Description EAN Part Nr.
Nozzle BIS-V, BIS-P 8714345148892 3.200.003
Nozzle BIS-PE 8714345148908 3.200.004
Nozzle BIS-HY new 8714345187648 3.200.007
Nozzle Extension 200 mm 8714345148915 3.200.005
Nozzel Extension 1000 mm 8714345148922 3.200.006
 
Description EAN Part Nr.
Piston Plug #24 8714345148939 3.810.242
Piston Plug #28 8714345148946 3.810.282
Piston Plug #32 8714345148953 3.810.322
Piston Plug #35 8714345148960 3.810.352
Piston Plug #38 8714345148977 3.810.382
 
         
  Adapter SDS+/M6   Extension Rod M6  
     
 

Adapter SDS+ with Internal Threading M6
Length 110 mm • Qty./1

  For the use with Adapter and Brushes.
Length 185 mm Qty./1
 
 
Description EAN Part Nr.
Adapter SDS+ 8714345149158 3.820.001
 
Description EAN Part Nr.
Extension Rod M6 8714345149165 3.820.002
 
  Steel Brushes      
   
 
Brush Rods EAN Part Nr.
Ø12 M8 8714345149042 3.820.012
Ø14 M10 8714345149059 3.820.014
Ø16 M12 8714345149066 3.820.016
Ø18 M14 8714345149073 3.820.018
Ø20 M16 8714345149080 3.820.020
Ø27 M20 8714345149103 3.820.027
Ø30 M24 8714345149110 3.820.030
Ø34 M27 8714345149127 3.820.034
Ø37 M30 8714345149134 3.820.037
 
Brush Dowels EAN Part Nr.
Ø14 Ø8 8714345149059 3.820.014
Ø16 Ø10 8714345149066 3.820.016
Ø18 Ø12 8714345149073 3.820.018
Ø20 Ø14 8714345149080 3.820.020
Ø24 Ø16 8714345149097 3.820.024
Ø27 Ø20 8714345149103 3.820.027
Ø30 Ø22 8714345149110 3.820.030
Ø34 Ø25 8714345149127 3.820.034
Ø37 Ø28-32 8714345149134 3.820.037
 
         
    Sleeves  
   

For the use in hollow masonry & blocks • Qty./100

Installation Dimensions

Sleeve Drill Ø Drill Depth For Rods
Ø 9 x 50 Ø12 55 M6 - M8
Ø13 x 85 Ø16 90 M8 - M12
Ø13 x 130 Ø16 140 M8 - M12
Ø18 x 85 Ø20 90 M12 - M16

Ordering info

Sleeve EAN Part Nr.
Ø 9 x 50 8714345055572 3.200.950
Ø13 x 85 8714345055589 3.201.385
Ø13 x 130 8714345056340 3.213.130
Ø18 x 85 8714345149011 3.201.885
 
         
 

Logo B+BTec

   
Contact General Products
Munterij 8 Privacy & Cookie Statement Core Drilling
4762 AH Zevenbergen On-Site with B+BTec Structural Anchoring
  Website B+BTec Netherlands Concrete Cutting
The Netherlands Website B+BTec USA Hammer Drilling
    Tile & Stone
T +31 168 331 260    
F +31 168 331 280   Folow us on:
E info@bbtectools.com
   
© Copyright 2010-2020 B+BTec. All Rights Reserved. B+BTec, Karat & Diamond3 are Registered Trademarks.